Skip to content
01282 429061
Boiler help

How to Repressurise a Boiler, and Fix Low or High Boiler Pressure

Boiler pressure low? How to repressurise a combi or system boiler with a filling loop or key, the right pressure (1 to 1.5 bar) and what to do if it is too high.

Quick answer: to repressurise a combi or system boiler, switch the boiler off and let it cool, find the filling loop (usually underneath the boiler), then slowly open the valves until the pressure gauge reads about 1 to 1.5 bar. Close the valves fully and switch the boiler back on. If the pressure drops again within days, the system is losing water and needs checking by an engineer.

What should my boiler pressure be?

With the heating off and the system cold, the gauge on the front of most combi and system boilers should read between 1 and 1.5 bar. Baxi describes a normal range as 1 to 2 bar, because the pressure rises a little as the water heats up. Check your own boiler manual, as some models show a green band on the gauge.

Gauge reading (cold) What it means What to do
Below 1 bar Pressure too low. The boiler may stop working or show a fault code. Top it up using the steps below.
1 to 1.5 bar Normal Nothing
Above 2 bar when cold Higher than it should be See boiler pressure too high, below.
3 bar The pressure relief valve opens to protect the boiler Stop and call an engineer.

How to repressurise a boiler with a filling loop

Most combi boilers have an external filling loop: a silver braided hose with a tap at each end, connected between two pipes under the boiler. Worcester Bosch gives these steps:

  1. Switch the boiler off and let the system cool, so you get a true reading.
  2. Check the hose is connected at both ends. If it has been removed, screw it back on hand tight.
  3. Open the first valve (the one on the cold mains side), then slowly open the second. You will hear water flowing into the system.
  4. Watch the gauge. Close both valves as soon as it reaches about 1 to 1.5 bar. Do not overfill.
  5. Make sure both valves are fully closed. A valve left slightly open keeps pushing the pressure up.
  6. Switch the boiler back on and reset it if the display asks you to. Some manufacturers recommend removing the hose afterwards.

How to repressurise a boiler with a filling key

Some Worcester Bosch combi boilers use a built-in filling link with a removable key instead of a hose. Worcester says the key is usually kept in a flap under the boiler and fits into a port at the front underside. Push the key in, line up the arrow with the open padlock symbol and turn it until the gauge reads just over 1 bar, then turn it back to the closed position and remove the key. Filling arrangements differ between makes and models, so if your boiler has neither a hose nor a key, follow the instructions in your manual.

Why is my boiler losing pressure?

A small drop after bleeding radiators is normal, because letting air out lowers the pressure. If you top it up and it keeps falling, the usual causes are:

  • A leak on a radiator valve, a joint or a pipe. Look for damp patches, rust marks or white crusty residue under radiators and around valves.
  • The pressure relief valve letting water out. This drains through a small copper pipe that usually runs through the wall outside. If that pipe is wet or dripping, the valve needs looking at.
  • A fault inside the boiler, such as the expansion vessel losing its charge. This is a job for an engineer.

Boiler pressure too high: what to do

Baxi lists the common causes of high pressure as overfilling, a filling loop left open, or a radiator that has been removed and refilled. To bring it down:

  1. Check both filling loop valves are fully closed.
  2. Switch the heating off and let the system cool.
  3. Bleed a radiator with a radiator key, catching the water with a cloth, and watch the gauge until it falls to about 1.5 bar. Our guide to bleeding a radiator shows how.
  4. If the pressure climbs back up, or the relief pipe outside is dripping, stop and call an engineer.

When to call a Gas Safe registered engineer

Call an engineer if the pressure keeps dropping, rises above 3 bar, the relief pipe outside is dripping, or there is water inside or under the boiler. Never take the front casing off a gas boiler yourself. In Burnley and East Lancashire, call us on 01282 429061 and we will put you in touch with the Gas Safe registered engineers we work with.

Is it time for a new boiler?

If your boiler loses pressure often and is more than 10 to 15 years old, repairs can stop being worth it. You can see a fixed, fitted price for a new boiler in Burnley in about a minute. Filling loops, radiator keys and inhibitor are in stock at our Burnley trade counter.

Sources (checked 18 November 2026)

  • Worcester Bosch, How to repressurise your boiler: worcester-bosch.co.uk/heating-advice/boiler-pressure
  • Baxi, How to fix high boiler pressure: baxi.co.uk/help-and-advice/how-to-guides/how-to-fix-high-boiler-pressure
  • British Gas, Boiler pressure advice: britishgas.co.uk

Checked for accuracy on 18 November 2026

Graeme Palmer
Premier Gas Burnley

Glynn Abbott
Glynn Abbott Services, Gas Safe registered engineer no. 945983

Researched and written by the Premier Gas Burnley team, the plumbers merchant at Bridge End Mill, Wiseman Street, Burnley, trading since 1968. Facts are taken from the sources listed. Gas work is carried out only by the Gas Safe registered engineers we work with.

WhatsApp us