Skip to content
01282 429061
Radiators and heating

How to Bleed a Radiator, and Fix Radiators Cold at the Top or Bottom

How to bleed a radiator step by step, why a radiator is cold at the top or bottom, how often to bleed radiators and how to balance them so every room heats up.

Quick answer: to bleed a radiator, switch the heating off and let the radiators cool. Put a cloth under the bleed valve at the top corner, turn it anticlockwise with a radiator key until you hear air hissing, and close it clockwise as soon as water appears. Then check the boiler pressure gauge is still about 1 to 1.5 bar and top it up if it has dropped.

Do my radiators need bleeding?

Turn the heating on and carefully feel each radiator from top to bottom once it has warmed up.

What you feel Likely cause Fix
Cold at the top, warm at the bottom Trapped air Bleed the radiator
Cold at the bottom, warm at the top Sludge sitting in the radiator The system needs flushing
Some radiators hot, others barely warm The system is not balanced Balance the radiators
Gurgling or banging noises Air in the system Bleed the radiators

What you need

  • A radiator key (some modern valves take a flat screwdriver instead)
  • An old towel or cloth, and a small container

How to bleed a radiator step by step

These steps follow Baxi’s advice:

  1. Turn the heating on and feel the tops of the radiators to find the ones with cold spots.
  2. Switch the heating off and wait for the radiators to cool, so you are not sprayed with hot water.
  3. Find the bleed valve, a small square valve at one of the top corners of the radiator. Hold the cloth underneath it.
  4. Turn the key anticlockwise by about a quarter to half a turn. You will hear a hiss as the air escapes.
  5. Close the valve clockwise as soon as water starts to come out, and wipe up any drips. Do not overtighten it.
  6. Repeat on the other radiators. Start with the ones downstairs and work up. The highest radiator in the house, often a towel rail, usually collects the most air.
  7. Check the boiler pressure. Bleeding lets water out of the system, so the gauge may have dropped. If it is below 1 bar, repressurise the boiler.
  8. Turn the heating back on and check the radiators heat evenly.

Radiator cold at the bottom

If a radiator is warm at the top and cold at the bottom, bleeding will not fix it. Sludge (rust and debris from inside the system) has settled in the bottom of the radiator. Baxi recommends having the system flushed by a Gas Safe registered installer, then dosed with an inhibitor to protect it. Fitting a magnetic system filter helps stop the sludge coming back.

Radiator cold at the top

Cold at the top means trapped air, so bleed it using the steps above. If you find yourself bleeding the same radiator every few weeks, or the water from the bleed valve is dark and rusty, Baxi says it can point to a leak or corrosion somewhere in the system. That is worth getting checked.

How often should you bleed radiators?

Baxi suggests checking your radiators at least once a year. Early autumn, before the heating goes on full time, is a good time to do it. Bleed them any time you notice cold spots or gurgling.

How to balance radiators

If the radiators nearest the boiler get hot quickly and the ones furthest away stay lukewarm, the system needs balancing. The lockshield valve (the one under a plain plastic cap, at the opposite end to the thermostatic valve) controls how much hot water each radiator takes.

  1. Turn the heating off and let it cool. Open every thermostatic valve fully and open every lockshield valve.
  2. Turn the heating on and note the order in which the radiators warm up.
  3. On the radiator that heats up first, close the lockshield valve, then open it about a quarter of a turn.
  4. Work through the radiators in the order they warmed up, opening each lockshield a little more than the last. The furthest radiator may need it fully open.
  5. For a more accurate result, Screwfix advises using a radiator thermometer and aiming for a difference of about 12°C between the pipe going in and the pipe coming out of each radiator.

When to call a Gas Safe registered engineer

Call an engineer if radiators stay cold after bleeding and balancing, if the boiler keeps losing pressure, or if you see water leaking from a valve or pipe. In Burnley and East Lancashire, call us on 01282 429061 and we will put you in touch with the Gas Safe registered engineers we work with.

Radiator keys, thermostatic valves, lockshield valves, inhibitor and magnetic filters are all in stock at our Burnley trade counter. If your radiators and boiler are past their best, see a fixed price for a new boiler.

Sources (checked 18 November 2026)

  • Baxi, How to bleed a radiator: baxi.co.uk/faqs/how-to-bleed-a-radiator
  • British Gas, Radiator cold at the top: britishgas.co.uk
  • Screwfix, How to balance radiators: screwfix.com

Checked for accuracy on 18 November 2026

Graeme Palmer
Premier Gas Burnley

Glynn Abbott
Glynn Abbott Services, Gas Safe registered engineer no. 945983

Researched and written by the Premier Gas Burnley team, the plumbers merchant at Bridge End Mill, Wiseman Street, Burnley, trading since 1968. Facts are taken from the sources listed. Gas work is carried out only by the Gas Safe registered engineers we work with.

WhatsApp us